canon sx 800 user manual

canon sx 800 user manual

Major Features Smooth and Beautiful Imaging Capability Incorporation of AISYS, Canon's unique optical engine, and LCOS (Liquid Crystal On Sili- con) achieves high brightness, high contrast ratio, and smooth and beautiful lattice-free images. This manual pro- vides detailed information on how to use the projector. Read this manual thoroughly to make the most of your projector and ensure safety. Important Information and Quick Start Guide First read document. Connecting the Projector Connecting to the Computer (P40 Connecting to AV Equipment Connecting a Digital Camera (SX80 II) (P48, P114. This projector offers many convenient features and functions. Operating the projector properly enables you to manage those features and maintain it in good condition for a long period. Do not stare directly into the lens if possible, as doing so may result in eye damage. Be especially careful that children do not stare directly into the beam. All the safety and operating instructions should be read before beginning to operate the product. Read all of the instructions given here and retain them for later use. Unplug this projector from the AC power supply before cleaning. Never spill liquid of any kind onto the projector. Do not install the projector near the ventilation duct of air-conditioning equipment. Ask the Canon service representative to clean and check the inside of the projector and replace the lamp. You need an optional ceiling mounting hanger (part number: RS-CL10) and an optional ceil- ing-mount pipe (part number: RS-CL08 or RS-. The remote control allows you to operate all functions of the projector. POWER button (P49, P68) Turns the projector on or off. ASPECT button (P66) Toggles between the modes for aspect ratio. INPUT button (P55) Switches among input signals.Receives an analog PC (ANALOG PC-1) or a digital signal (DIGITAL PC, SX80 II). They receive the following audio sig- nals in order from the left.Performing the Auto Setup (P52) Image projected properly.http://goldengrainsdubai.com/public_html/userfiles/canon-powershot-sd880-is-user-manual-download.xml

• 1.0.

Selecting an Input Signal (P54) Image projected properly. Adjusting the Image (P56) You can point it up as far as 10 degrees. The keystone distortion of the projecting image can be corrected with the auto keystone (P52) or by using the keystone distortion adjust function (P60). Using an audio cable with a built-in resistor turns down the sound. Using an audio cable with a built-in resistor turns down the sound. Before connecting the cables, turn off both the projector and AV equipment. The description provided here is just examples.Projector To AUDIO OUT Use an audio cable without a built-in resistor. Using an audio cable with a built-in resistor turns down the sound. Connecting the Projector Commercial audio cable Speaker. You can connect a PictBridge enabled digital camera, a digital video camera, an USB flash memory, or an USB memory card reader to directly project images. Digital camera Projector USB flash memory. Wait until the indicator turns a steady red. Press the OK button. SX80 MarkII SX800. Remote control The currently active input signal is marked with a circle and highlighted in orange. An input signal that is ready for projection is displayed in white. When no signal is received, it is displayed in gray. Change the projector installation position if your desired image is too large or too small to adjust it with the zoom function. (P35) Press the ZOOM button to pop up a window shown at the lower right. Remote control Select this when you use a screen with aspect ratio of 4:3. 16:9 Select this when you use a screen with aspect ratio of 16:9. 16:9 D. image shift Select this when you use a screen with aspect ratio of 16:9. The selection is toggled among types for aspect ratios by pressing the ASPECT button.Remote control Press the POWER button again while the confirmation message is displayed.Remote control Press the button to blacken out the image. Press the button again to show the image. Remote control Press the button.Press the button.http://beach.domyno.cz/userfiles/canon-powershot-sd960-is-manual.xml

A part of the image is enlarged each time pressed. Then the timer returns to 00:00. Press the OK button to accept your setting and then press the MENU button. Press the OK button to accept your setting and then press the MENU button. Adjusts the tracking when the image dis- torts or flickers. The entire input signals (100%) are pro- jected. When the menu has been moved to the desired position, press the OK or MENU button. Setting Display Status. A screen for capturing images is dis- played. Black The screen is all black. Setting Display Status. Select this when you use a screen with aspect ratio of 4:3. You can select it also with the IMAGE but- ton on the remote control. SX80 MarkII Press the OK button to accept your setting and then press the MENU button. Dynamic gamma is disabled. Weak Dynamic gamma is used a little. You can enable or disable this mode also with the LAMP button on the remote con- trol. You need to press the POWER button to turn on the projector. Disables the key lock. Main unit Prohibit the operation from the main unit. Shows the guide screen. Press the OK button to accept your setting and then press the MENU button. Normal The menu is displayed for 30 sec- onds. SX80 MarkII Information shown Item Model name Model name of this projector Input signal Details of the input signal currently selected “Type of signal”, “resolution of signal”, “frequency”. For the up-to-date information regarding PictBridge, visit Cannon's web- site ( ) or PictBridge's website ( ). Connecting a Digital Camera Turn the projector power on. With Canon digital camera If the projector does not recognize the device or communi- cation is disabled, the screen as shown in the right appears. Connect a USB flash memory to the USB terminal. Use a USB cable to connect a digital camera or USB memory card reader. Be sure to use the USB cable supplied with the equipment connected to the projec- tor.

In the USB file browser, you can select the image file to be projected by operating the file list in the USB memory device. If a USB memory card reader having multiple memory slots is connected, the drive (mem- ory slot) list is displayed in the file list. To connect via the network, an IP address must be assigned to the projector. Set an IP address by following the steps below. Follow the step 3 to 6 to restore the network setting to the original setting. Setting an IP Address (SX80 II) The password input screen appears. The supported web browsers is Microsoft Internet Explorer 6 or later.Authentication and Encryption Protocols SNMP V3 for the projector uses the DES-CBC for the authentication and encryption protocols.Temperature abnormality The temperature inside the projector is too high for some reason or the outside air temperature is higher than the specified one. If the problem is inside the projector,. The projector control screen appears.Cause The power cord is not connected correctly. The power cord has just been con- nected. The lamp cover is open. The safety device has activated because you put the projector in the carrying bag during the cooling fan was rotating. The displayed image is not the same as that displayed on the computer.Cause The image is out of focus. The distance to the screen is too short. The projector is not placed straight in front of the screen. The projector has been moved to a place where the temperature var- ies a lot. Cause Batteries are not installed properly or they have run out. You are operating the remote con- trol from the outside of the remote control operating range. Wait until the projector cools down sufficiently (more than 1 hour) before cleaning the projector. Should the air filter become clogged with dust, the pro- jector may be damaged since it will block the air flow into the projector and raises the internal temperature of the projector.

As shown in the figure, insert a flat- head screwdriver in the gap and remove the lamp cover by raising it. To project an image on the whole screen, select the most appropriate screen aspect ratio and aspect according to the aspect ratio of the screen and input signal type.The image is expanded fully on the screen with the screen aspect maintained. If your computer or AV equipment is compatible with any one of these signal types, the projector's auto PC function selects the input signal type to project an image appropriately. ANALOG RGB Resolution Signal type. The reproduc- ibility of the bright tone is mainly changed. Since you can adjust the gain for each RGB color in this projector, you can also adjust colors. Use a D-sub computer cable for connection. For more detailed information, refer to the instruction manual that comes with the ceiling-mount hanger RS-CL10. Upon completion of the download, the PDF file opens automatically. You may download and use the Content solely for your personal, non-commercial use and at your own risks. Canon shall not be held liable for any damages whatsoever in connection with the Content, (including, without limitation, indirect, consequential, exemplary or incidental damages). You shall also not (and shall not let others) reproduce, modify, reformat or create derivative works from the Content, in whole or in part. This page requires Javascript. Modify your browser's settings to allow Javascript to execute. See your browser's documentation for specific instructions. To install your download click on the name of the downloaded file.The driver may be included in your OS or you may not need a driver.

Recommended Driver(s) File Name Date File Size Optional Driver(s) File Name Date File Size Recommended Software File Name Date File Size Optional Software File Name Date File Size Recommended Manual(s) File Name Date File Size Optional Manual(s) File Name Date File Size During the warranty period for the Lamp, Canon will, in its sole discretion and without charge, exchange a defective Lamp for a new Lamp. Except as set forth herein, this warranty does not cover consumable items as to which there is no warranty or replacement. Warranty exchange or replacement does not extend the original warranty periods of the Equipment. When returning Equipment for warranty service, shipping charges must be prepaid and the Equipment must be shipped in its original carton or box, or an equivalent. A bill of sale, or other proof of purchase, as well as a description of the problem, must be enclosed. This Limited Warranty shall only apply if the Equipment is used in conjunction with compatible computers, peripheral equipment and software. The sole warranty, if any, with respect to such non-Canon brand item is given by the manufacturer or producer thereof.Nor does this warranty i) extend to any Equipment on which the original identification marks or serial numbers have been defaced, removed or altered, ii) cover the adjustment of customer-operated controls as explained in the instruction manual, iii) extend to any external interface equipment, iv) apply to the cabinet or cosmetic parts, knobs or routine maintenance, or v) cover uncrating, set up, installation, removal of the Equipment for repair or reinstallation of the Equipment after repair.If the problem cannot be corrected over the telephone, you will be asked to follow the applicable procedures for MAIL — IN SERVICE. Note that a dated proof of purchase is required at the time of service. MAIL — IN SERVICE MAIL-IN SERVICE is a program under which your Product is repaired by a Canon U.S.A.

or a Canon Canada authorized service center. You will be given the name, address and phone number of an authorized service center for the Product. It is your responsibility to properly package and send the defective Product, together with a copy of your dated proof of purchase, a complete explanation of the problem and a return address to the authorized service center at your expense. Do not include any other items with the defective Product. The Product covered by this limited warranty and proven to be defective upon inspection will be repaired and returned to you without charge by the authorized service center. Any Product received by the authorized service center that is not covered by the limited warranty will be returned unrepaired, or at the discretion of the authorized service provider, you may receive a written estimate of repair at such cost as the service center may establish from time to time. During the warranty period for the Lamp, Canon will, in its sole discretion and without charge, exchange a defective Lamp for a new Lamp. Except as set forth herein, this Limited Warranty does not cover consumable items as to which there is no warranty or replacement. ADVANCED WARRANTY EXCHANGE SERVICE PROGRAM The Advanced Warranty Exchange Service Program (the “Program”) is a program in which a replacement Product is sent to you by Canon and you return to Canon the Product you originally purchased, which becomes the property of Canon. To use the Program, contact a Canon Customer Care Representative using the applicable Canon contact information below. The Canon Customer Care Representative will attempt to diagnose the nature of the problem and, if possible, correct it over the telephone. If the Canon Customer Care Representative determines that the Product is eligible for coverage under this Limited Warranty and that the problem cannot be corrected over the telephone, a reference number and an End User Activation Form will be issued to you.

Submission of your signed End User Activation Form (the “Form”) will activate your request for an exchange, and the terms and conditions in the Form will govern Canon’s provision of services under the Program. When you call, have your Product serial number and your date of purchase available to expedite service. A Canon Customer Care representative will attempt to diagnose the nature of the problem and correct it over the telephone. If the problem cannot be corrected over the telephone, you will be asked to follow the applicable procedures for MAIL-IN SERVICE. This requirement will be satisfied by providing a copy of your dated bill of sale. It is your responsibility to properly package and send the defective Product, together with a copy of your dated proof of purchase, a complete explanation of the problem and a return address, to the authorized service center at your expense. The Product covered by this Limited Warranty and proven to be defective upon inspection will be repaired and returned to you without charge by the authorized service center. Any Product received by the authorized service center that is not covered by the Limited Warranty will be returned unrepaired, or at the discretion of the authorized service center, you may receive a written estimate of repair at such cost as the authorized service center may establish from time to time. The sole warranty, if any, with respect to such non-Canon brand item is given by the manufacturer or producer thereof.Nor does this warranty i) extend to any Equipment on which the original identification marks or serial numbers have been defaced, removed or altered, ii) cover the adjustment of customer-operated controls as explained in the instruction manual, iii) extend to any external interface equipment, iv) apply to the cabinet or cosmetic parts, knobs or routine maintenance, or v) cover uncrating, set up, installation, removal of the Equipment for repair or reinstallation of the Equipment after repair.

During the warranty period for the Lamp, Canon will, in its sole discretion and without charge, exchange a defective Lamp for a new Lamp. The sole warranty, if any, with respect to such non-Canon brand item is given by the manufacturer or producer thereof.If the problem cannot be corrected over the telephone, you will be asked to follow the applicable procedures for MAIL — IN SERVICE. Authorized service center information can be obtained by visiting www.canontechsupport.com (US customers only) or by contacting the Canon U.S.A., Customer Care Center or Canon Canada Customer Information Centre at 1-800-OK-CANON (1-800-652-2666). Any Product received by the authorized service center that is not covered by the limited warranty will be returned unrepaired, or at the discretion of the authorized service provider, you may receive a written estimate of repair at such cost as the service center may establish from time to time. Scroll down to easily select items to add to your shopping cart for a faster, easier checkout. Visit the Canon Online Store It is compatible with a variety of ceiling mounts.It is compatible with a variety of ceiling mounts.It is compatible with a variety ceiling mounts.It is compatible with a variety ceiling mounts.It can be secured to either wood ceiling beams or concrete using commercially available bolts. The mount includes anti-fall wires to prevent accidents when unhitching your projector.It can be secured to either wood ceiling beams or concrete using commercially available bolts. The mount includes anti-fall wires to prevent accidents when unhitching your projector.Lamp life is 2500 hours in Quiet Mode and 2000 hours in Normal mode. Please check your inbox, and if you can’t find it, check your spam folder to make sure it didn't end up there. Please also check your spam folder. You can easily find settings for each function. ( P76 - P112 ) This manual provides detailed information on how to use the projector.

Read this manual thoroughly to make the most of your projector and ensure safety. Operating the projector properly enables you to manage those features and maintain it in good condition for a long period. If the problem still persists, contact the service center or the dealer where you purchased the projector. Be especially careful that Minimum clearances must be Do not cover the ventilation slot on the Unplug this projector from the AC power supply before cleaning. Do not use liquid or aerosol cleaners on the projector. Use a damp cloth for cleaning. This will prevent damage due to lightning and power surges. The projector may fall, causing serious injury to a child or adult, and serious damage to the projector. Use only with a cart or stand recommended by the manufacturer, or sold with the projector. Wall or shelf mounting should be carried out in accordance with the manufacturer's directions, and should use a mounting kit approved by the manufacturers. Sudden stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn. This projector should never be placed near or over a radiator or heat register. Never spill liquid of any kind onto the projector. If you are not sure of the type of power supplied, consult your authorized dealer or local power company. Do not allow anything to rest on the power cord. Do not locate this projector where the cord may be damaged by people walking on it. Refer all servicing to qualified service personnel. Adjust only those controls that are covered in the operating instructions as improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the projector to normal operating condition. Unauthorized substitutions may result in fire, electric shock, or injury. Should you be unable to This product should be handed over to a designated collection point, e.g.

, on an authorized one-for-one basis when you buy a new similar product or to an authorized collection site for recycling waste electrical and electronic equipment (EEE) and batteries and accumulators. Improper handling of this type of waste could have a possible impact on the environment and human health due to potentially hazardous substances that are generally associated with EEE. Your cooperation in the correct disposal of this product will contribute to the effective usage of natural resources.Operation is subject to the following two conditions: These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: If such changes or modifications should be made, you could be required to stop operation of the equipment. Failure to do so may cause explosion, heat generation, fire, or leakage of the battery fluid. Failure to do so may cause explosion, heat generation, fire or leakage of the battery fluid. Do not mix batteries of different types. There is no guarantee that all lamps will last for the same period of time. Some lamps may fail in a shorter period of time than other similar lamps. Open win- Warning dows and doors for ventilation. Always keep your face away from the exhaust vent when the projector is operating to avoid inhaling mercury vapors or to prevent it from getting in your eyes or mouth.

Ask the Canon service representative to clean and check the inside of the projector and replace the lamp. Replace the lamp with a new one immediately if such is the case. Do not subject the projector to strong shocks or vibrations or turn it down. For details, see P23. Do not put the projector in the carrying bag until the cooling fan stops rotating. The projector may be damaged due to the heat. The projector may be damaged if you put it in the bag without replacing the adjustable foot. When carrying the projector with it put in the carrying bag, do not give a shock to it, drop it, or place anything on it. The projector may be damaged or malfunctioned. Put the projector in an impact-resistant transport case if such is the case. In particular, keep children away from these areas. Do not put anything that may deform or discolor due to heat on the projector. Observe the following. It may become hot, resulting in accident or injury. Incorrect installation may cause The projector may fall causing a personal injury. It may cause a fire or an electric shock. Otherwise, it may damage the projector due to bad exhaust ventilation. Optical parts such as a lens and mirror may be stained, resulting in poor picture quality. Otherwise, it may be damaged. Wait until condensation evaporates and normal picture is shown. Doing so may cause malfunction. The ranges of the operating and storage temperatures are as shown below: Contact your dealer. Do not put the projector in the carrying bag until the cooling fan stops rotating. Replace the adjustable foot to prevent the damage on the projector. The projector may be damaged or malfunctioned. Failure to do so will result in Failure to do so will result in fire hazards or mal- Failure to do so will result in fire haz- You need an optional ceiling mounting hanger (part number: RS-CL10) and an optional ceil- ing-mount pipe (part number: RS-CL08 or RSCL09) when appropriate.

Contact the dealer where you purchased the projector for more detailed information. They receive the following audio signals in order from the left. It outputs the audio signal corresponding to the projected image signal. Doing so could damage it. In a bright For ceiling mounting or rear projection, you have to invert the projected image. ( P87 ) Using an audio cable with a built-in resistor turns down the sound. Using an audio cable with a built-in resistor turns down the sound. For more detailed information, refer to the manual for the connecting AV equipment. Using an audio cable with a built-in resistor turns down the sound. Using an audio cable with a built-in resistor turns down the sound. Using an audio cable with a built-in resistor turns down the sound. Wait until the indicator turns a steady red. Press the OK button to make the countdown window disappear. Perform the appropriate operation depending on the following situations. You can select a language to be used by the projector for displaying menus and messages in the window. Select the desired language with the pointer buttons and press the OK button. Post your question here in this forum. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share. Note that email addresses and full names are not considered private information. Please mention this; Therefore, avoid filling in personal details. Please enter your email address. Should the air filter become clogged with dust, the pro- jector may be damaged since it will block the air flow into the projector and raises the internal temperature of the projector. The following screen is displayed when turning on the projector if the air filter needs to be cleaned. Clean the air filter if such is the case.

Follow the following procedure when replacing the air filter. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. The result is superb edge-to-edge sharpness across the image field. A 10:0 lens offset maintains the optical center of the lens when the projector is tilted up and sidesteps the deleterious effects of key-stoning. The projector's 3000 ANSI lumens of brightness is more than adequate to meet the challenge of the most difficult ambient light situations. The SX800 is compatible with wide variety of image input sources, each paired with an audio input. Switching the image source automatically links it with the corresponding audio source. As a further convenience, when powering up, Auto Setup selects the active input and sets the vertical keystone correction. A 10:0 lens offset compensates for tilt and helps prevent keystone distortionLet us know YOUR RECENTLY VIEWED ITEMS Browsing History ON Clear History Not responsible for typographical or illustrative errors. Checking your browser before accessing This process is automatic. Your browser will redirect to your requested content shortly. Used: Very GoodTested, cleaned and reset to manufacture specs. All ready to go, will include power cable and compute VGA cables (no original remote). Ships fast with FREE insurance and tracking.Please try again.Please try again.Please choose a different delivery location.In order to navigate out of this carousel please use your heading shortcut key to navigate to the next or previous heading. Full content visible, double tap to read brief content. Please try your search again later.Canon projectors are no exception. The family of Canon projectors includes the REALiS line of bright, high resolution,.To calculate the overall star rating and percentage breakdown by star, we don’t use a simple average.

Instead, our system considers things like how recent a review is and if the reviewer bought the item on Amazon. It also analyzes reviews to verify trustworthiness. In order to navigate out of this carousel please use your heading shortcut key to navigate to the next or previous heading. Major Features Smooth and Beautiful Imaging Capability Incorporation of AISYS, Canon's unique optical engine, and LCOS (Liquid Crystal On Sili- con) achieves high brightness, high contrast ratio, and smooth and beautiful lattice-free images.Canon - Projector. The site is interesting in that there is a TOP category. We also share information about your use of our site with our social media, advertising and analytics partners who may combine it with other information that you’ve provided to them or that they’ve collected from your use of their services. Which lobe of the mind is indicated by the letter b?B is in the area of Broca's area. If you look at the region of the left hemisphere of the mind, you will observe that the letters will be arranged vertically. Those letters that fall along with letters are assigned to the left hemisphere. Therefore, in this scenario, it will fall in the left lobe of their brain. The names of these letters will change if you examine the word that lobe of the brain is indicated by the letter b? After the letters are arranged horizontally, then what will occur is that the letters will be arranged horizontally. If you examine the word which lobe of the brain is indicated by the letter b, then what happens is that if you look back on the region of the left hemisphere, you will see that it will be beneath the region of the ideal hemisphere, right here in the left lobe of their brain. Below are the letters in the bible A-Z, now they're again separated and today it's been branded which lobe of the brain is indicated by the letter b? Which lobe of the brain is indicated by the letter b? It is the left lobe.